Non-Destructive Evaluation of Concrete: From Surface Hardness to Corrosion Detection
DOI:
https://doi.org/10.32628/IJSRCE2154962Keywords:
Non-destructive testing, strength, durability, Surface hardness, Corrosion detection, Rebound hammer, Penetration resistanceAbstract
Non-destructive testing (NDT) methods are increasingly being used to assess the strength, uniformity, and durability of concrete structures. This paper reviews the most successful NDT methods for concrete, discussing their principles, applications, limitations, and interpretation. Surface hardness methods, such as the Schmidt Rebound Hammer test, estimate concrete strength by measuring the rebound of a plunger striking the surface. Penetration resistance methods, like the Windsor probe system, measure the depth of penetration of a probe shot into the concrete. Pull-out and pull-off tests measure the force required to extract an embedded insert or pull off a surface disc, respectively, to estimate strength. Resonant frequency methods use the natural vibration of concrete to determine its elastic properties and strength. The maturity method estimates early-age strength by monitoring the temperature history of the concrete during curing. Permeation tests, such as the rapid chloride permeability test, assess the ability of concrete to resist the ingress of deleterious substances. Ultrasonic pulse velocity and impact-echo methods use stress waves to detect internal flaws, cracks, and delamination’s. Half-cell potential measurements are used to assess the corrosion risk of embedded steel reinforcement. The successful application of these methods requires an understanding of the principles underlying the test methods, the factors influencing the test results, and the limitations of the methods. Establishing reliable correlations between NDT results and concrete properties for specific mix designs and testing conditions is essential for accurate interpretation. Advances in sensor technology, data analysis techniques, and multisensory data fusion are expected to enhance the capabilities and reliability of NDT methods for concrete structures in the future.
Downloads
References
Akashi, T., & Amasaki, S. (1984). Study of the Stress Waves in the Plunger of a Rebound Hammer at the Time of Impact. Detroit: American Concrete Insitute.
Bickley, J. (1982). The Variability of Pullout Tests and In-Place Concrete Strength. Concrete International, ACI, Vol.4, No. 4, 44-51.
Carino, N. (2004). Pullout Test. In V. Malhotra, & N. Carino, Handbook on Nondestructive Testing of Concrete (pp. 24-56). New York: CRC Press.
Carino, N. (2001). The Impact-Echo Method: An Overview. Structures Congress & Exposition (pp. 18-36). Washington, D.C.: American Society of Civil Engineers. DOI: https://doi.org/10.1061/40558(2001)15
Concrete Institute of Australia. (2008). Nondestructive Testing of Concrete. Sydney: Concrete Institute of Australia.
Doebling, S., Farrar, C., Prime, M., & Shevitz, D. (1996). Damage Identification and Health Monitoring of Structural and Mechanical Systems from Changes in Their Vibration Characteristics: A Literature Review. Los Alamos: Los Alamos National Laboratory. DOI: https://doi.org/10.2172/249299
Elsener, B., Müller, S., Suter, M., & Böhni, H. (1990). Corrosion monitoring of steel in concrete theory and practice. In C. Page, K. Treadway, & P. Bamforth, Corrosion of Reinforcement in Concrete Construction (pp. 348-350). New Yotk: Elsevier Applied Science.
Henderson, G., Basheer, P., & Long, A. (2004). Pull-Off Test and Permeation Tests. In V. Malhotra, & N. Carino, Handbook on Nondestructive Testing of Concrete (pp. 64-83). New York: CRC Press.
Jones, R. (1969). A review of the non-destructive testing of concrete. London: Institution of Civil Engineers.
Keiller, A. (1982). A preliminary investigation of test methods for the assessment of strength of in situ concrete - Technical Report 42.551. Wexam Springs: Cement and Concrete Association.
Kierkegaard-Hansen, P. (1975). Lokl-strength. Stockholm: Nordisk Betong.
Kolek, J. (1969). Non-destructive testing of concrete by hardness methods. London: Institute of Civil Engineers.
Malhotra, V. (2004). Surface Hardness Methods. In V. Malhotra, & N. Carino, Handbook on Nondestructive Testing of Concrete (pp. 1-9). New York: CRC Press. DOI: https://doi.org/10.1201/9781420040050
Malhotra, V., & Carette, G. (2004). Penetration Resistance Methods. In V. Maholtra, & N. Carino, Handbook on Nondestructive Testing of Concrete (pp. 10-23). New York: CRC Press.
McCann, D., & Forde, M. (2001). Review of NDT methods in the assessment of concrete and masonry structures. NDT&E International, 71 84. DOI: https://doi.org/10.1016/S0963-8695(00)00032-3
Naik, T., Malhotra, V., & Popovics, J. (2004). The Ultrasonic Pulse Velocity Method. In V. Malhotra, & N. Carino, Handbook on Nondestructive Testing of Concrete (pp. 84-97). New York: CRC Press.
Rayleigh, J. (1945). Theory of Sound (2nd Edition ed.). New York: Dover Press.
Saul, A. (1951). Principles underlying the steam curing of concrete at atmospheric pressure. Magazine of Concrete Research, II (6), 127-140. DOI: https://doi.org/10.1680/macr.1951.2.6.127
Shull, P. (2002). Nondestructive Evaluation: Theory, Techniques and Applications. New York: Marcel Dekker, Inc. DOI: https://doi.org/10.1201/9780203911068
Sohn, H., Farrar, C., & Hemez, F. (2004). A Review of Structural Health Monitoring Literature from 1996-2001. Los Alamos: Los Alamos National Laboratory.
Stanley, J. (1995). Nondestructive Testing Handbook 9: Special Nondestructive Testing Methods. Columbus: American Society of Nondestructive Testing.
Workman, G., & O. Moore, P. (2012). Nondestructive Testing Handbook 10: Overview. Columbus: American Society of Nondestructive Testing.
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
https://creativecommons.org/licenses/by/4.0
